Author Topic: CB40 Sale $25 plus shipping/postage  (Read 1083 times)

0 Members and 1 Guest are viewing this topic.

Offline BuNtEr

  • Administrator
  • Jr. Member
  • *****
  • Join Date: Apr 2018
  • Posts: 53
  • Karma: +0/-0
    • View Profile
CB40 Sale $25 plus shipping/postage
« on: October 22, 2018, 06:01:46 PM »
CB40 kit Sale info

$25 plus shipping/postage
Contact Peter on this Email: cb40switch@tpg.com.au
tell him what your needing CB40 or CB40A or the CB40 done for a PC122 or ST901, hard wired, and give him your postcode so he can give you a price on postage.

Features
Scan, up or down by the channel knob
Voltage Display (Real time 4 Digit)
Frequency Display (6 Digit)
Channel Display ( White Oled)

CB40
$25 (+ postage depending on location)
case (which is a half case protecting the Arduino because the top of the CB40 is your jumper connections), CB40,
OLED cable (4 pin),
Encoder cable (5 pin),
scan cable (3 pin),
power cable (2 pin),
white OLED 128x64 display,
EC11 rotary encoder.

Parts you will need to supply
Strong Double Sided tape
A few small Cable ties

Tools you will need to install the CB40
Phillips head screw driver
Soldering iron
Solder sucker
De-solder braid/wick
Wire Cutters
Solder
Hot melt glue gun and hot melt glue sticks

You must state if its for a PC122 or a Pearce Simpson ST901, or just a normal CB40 for all other radios, the CB40 for the 2 radios mentioned need to have all the wires hard wired instead of header pins due to the limited amount of space in these 2 radios.

https://www.youtube.com/watch?v=hLP80IojJ5w&t=3s

Installed into a Uniden PC122
https://www.youtube.com/watch?v=qesg-YlKWUg&t=6s

The Kit

Hardware
  • CB40 in a custom 3D printed case with holes on all sides so you can use cable ties to install it.
  • Encoder on a custom board
  • OLED screen (0.96" 128X64 White OLED I2C IIC Serial LCD LED SSD Display SSD1306)
Cables
  • Encoder Cable
  • OLED Cable
  • Power Cable
  • PLL cables
  • Scan Cable

No Warranty Given
  • On the OLED screen if you brake it or burn it out from getting the wires wrong way around.
  • On the CB40 if you damage it or burn it out due to wiring it wrong. or you in anyway try to modify the CB40 in any way thats not been instructed by the designer.

CB40 will be tested and have the latest firmware at time of shipping

--------------------------------------------------------------------------------------------------------------------------

                                                                          NOTICE
  • When ordering you must state type of encoder, is it spline shaft or D shaft, long or short, also if your going to install the unit into a PC122, tell the seller this as the CB40 for the PC122 has to have all cables hard wired to the CB40, as space in the PC122 is limited to sweet fuck all.
  • Please note that the screen will not be seen behind dark red defusers on the radio, you need to remove the red or green window, please also read the FAQ before you buy.
  • If your not sure if your confident enough to install this kit get a tech to install it for you, Contact Ray at Razor Radios Ray at Razor Radios to get a quote on installing the CB40 into your radio.
  • Please use contact email address to let the seller know what post code your from so they can give you a price on postage
--------------------------------------------------------------------------------------------------------------------------
« Last Edit: November 29, 2018, 06:35:43 PM by BuNtEr »

Offline BuNtEr

  • Administrator
  • Jr. Member
  • *****
  • Join Date: Apr 2018
  • Posts: 53
  • Karma: +0/-0
    • View Profile
Re: CB40 Sale $25 plus shipping/postage
« Reply #1 on: December 08, 2018, 10:35:18 PM »
This is the CB40 thats for the PC122 notice its hard wired, so it will fit inside the radio.