CB40 v2 kit Sale info
$25 plus shipping/postage in australia $8.95, for over seas please ask cost of shippingContact Peter on this Email: cb40switch@tpg.com.autell him what your needing CB40 v2 for
02A spindle shaft
Uniden D shaft
PC122 or ST901, these need to be hard wire
FeaturesScan, up or down by the channel knob
Voltage Display (Real time 4 Digit)
Frequency Display (6 Digit)
Channel Display ( White Oled)
CB40 v2$25 (+ postage depending on location)
Case
OLED cable (4 pin),
Encoder cable (5 pin),
scan cable (2 pin),
power cable (2 pin),
white OLED 128x64 display,
EC11 rotary encoder.
Addons for the kit 7 segment displays 3 and 2 digit
CB40 v2 LED Display ADDON7 segment 3 digit displays$15 AUD for red, green or yellow
$18 AUD for blue.
7 segment 2 digit displays$15 AUD for red
The displays come with Cable and amtel board and spacer, please state what radio when ordering so you get the correct display spacer
Parts you will need to supplyStrong Double Sided tape
A few small Cable ties
Tools you will need to install the CB40Phillips head screw driver
Soldering iron
Solder sucker
De-solder braid/wick
Wire Cutters
Solder
Hot melt glue gun and hot melt glue sticks
You must state if its for a PC122 or a Pearce Simpson ST901, or just a normal CB40 for all other radios, the CB40 for the 2 radios mentioned need to have all the wires hard wired instead of header pins due to the limited amount of space in these 2 radios.
The KitHardware- CB40 v2 in a custom 3D printed case.
- Encoder on a custom board
- OLED screen (0.96" 128X64 White OLED I2C IIC Serial LCD LED SSD Display SSD1306)
Cables- Encoder Cable
- OLED Cable
- Power Cable
- PLL cables
- Scan Cable
No Warranty Given- On the OLED screen if you brake it or burn it out from getting the wires wrong way around.
- On the CB40 v2 if you damage it or burn it out due to wiring it wrong. or you in anyway try to modify the CB40 v2 in any way thats not been instructed by the designer.
CB40 v2 will be tested and have the latest firmware at time of shipping
Here is a list of PLL's that will work with the CB40 v2, there are others we havent tested as yet that could work.
PLL LIST
PLL02A - SSB
PLL02A - AM
PLL02A - 1st Gen
uPD858 - SSB
uPD2812C - SSB
CB5479 - SHARP
LC7113 - SSB
LC7131 - SSB
MB8719 - 11.1125
MB8719 - 11.3258
NDC40013 - SSB
HD42851 - SSB
SM5104 - SSB
TC5080/81 SSB
uPD2816 - SSB
uPD2824 - SSB
uPD861 - Realistic
uPD861 - Panasonic
uPD861 - Superscope
Motorola - MC145106
--------------------------------------------------------------------------------------------------------------------------
NOTICE- When ordering you must state type of encoder, is it spline shaft or D shaft, long or short, also if your going to install the unit into a PC122, tell the seller this as the CB40 for the PC122 has to have all cables hard wired to the CB40, as space in the PC122 is limited to sweet fuck all.
- Please note that the screen will not be seen behind dark red defusers on the radio, you need to remove the red or green window, please also read the FAQ before you buy.
- If your not sure if your confident enough to install this kit get a tech to install it for you, Contact Ray at Razor Radios Ray at Razor Radios to get a quote on installing the CB40 v2 into your radio.
- Please use contact email address to let the seller know what post code your from so they can give you a price on postage
--------------------------------------------------------------------------------------------------------------------------